K-UNIT, KYPD, PULSE ISOLATOR, SIGNAL CONDITIONER, USED, WORKING GREAT For Sale

 K-UNIT, KYPD, PULSE ISOLATOR, SIGNAL CONDITIONER, USED, WORKING GREAT


This item has been shown 281 times.

Buy Now

K-UNIT, KYPD, PULSE ISOLATOR, SIGNAL CONDITIONER, USED, WORKING GREAT:
$45

K-UNIT, KYPD, PULSE ISOLATOR, SIGNAL CONDITIONER, USED, WORKING GREAT
Functions & Features • Galvanically isolating pulse rate signals • Input frequency = output frequency • Various outputs (relay, open collector and voltage pulses) • Excitation • Isolation up to 2000 V AC • High-density mounting Typical Applications • Isolating field pulse signals in order to reduce noises • Changing e.g. dry contact signal to e.g. 5 V signals
GENERAL SPECIFICATIONS Construction: Plug-in Connection: M3.5 screw terminals Screw terminal: Chromated steel (standard) or stainless steel Housing material: Flame-resistant resin (black) Isolation: Input to output to power Excitation adjustment: 5 – 12 V DC Detecting level adjustments (DC voltage pulse): 2 – 10 V Input pulse sensing: DC coupled Input filter: Provided with output code A2, M2, N2, H (time constant approx. 1 msec.) INPUT SPECIFICATIONS Excitation: Shortcircuit protection; approx. 150 mA at shortcircuit ■ Dry Contact Max. frequency: 100 kHz Pulse width time requirement: 5 μsec. min. (10 ms for output code A2, M2, N2, H) Sensing: 10 V DC @ 2.5 mA ON/OFF level: ≥ 5.5 kΩ /5.5 V for OFF ≤ 1.8 kΩ /4.5 V for ON ■ Voltage Pulse: Specify DC offset and amplitude. Max. frequency: 100 kHz Pulse width time requirement: 5 μsec. min. (10 ms for output code A2, M2, N2, H) Waveform: Square or sine Input impedance: 10 kΩ min. Input amplitude: 2 – 50 Vp-p Offset: 2 – 10 V Max. voltage between input terminals: 50 V • 5V, 12V, 24V Pulse Waveform: Square or sine Input impedance: 10 kΩ min. Detecting level INPUT 5 V PULSE 12 V / 24 V PULSE VH ≥ 2.25 V ≥ 5.25 V VL ≤ 1.75 V ≤ 4.75 V ■ Two-wire Current Pulse Max. frequency: 100 kHz Pulse width time requirement: 5 μsec. min. (10 ms for output code A2, M2, N2, H) Input resistance: Receiving resistor 220 Ω Maximum current: ± 50 mA Hi/Lo level: ≤ 5 mA for Lo, ≥ 15 mA for Hi 50V max. Amplitude Vinp-p t Volts DC Offset Voltage pulse waveform OUTPUT SPECIFICATIONS ■ Open Collector: 50 V DC @ 50 mA (resistive load) Maximum frequency: Output code A1: 100 kHz with load resistance ≤ 1 kΩ OUtput code A2: 10 Hz with load resistance ≤ 1 kΩ Saturation voltage: 0.5 V DC ■ Voltage Pulse: Rating (5 or 12 V) ± 10 % Maximum frequency: 100 kHz Load resistance: 1.5 kΩ min. for 5 V, 3 kΩ min. for 12 V L level: ≤ 0.5 V ■ Relay Contact: 120 V AC or 30 V DC @ 200 mA (resistive load) Maximum switching voltage: 250 V AC or 30 V DC Maximum switching power: 50 VA or 6 W Minimum load: 5 V DC @ 10 mA Maximum frequency: 0.5 Hz Relay life: 2 × 107 cycles (mechanical) 7 × 106 cycles (electrical) OUTPUT PULSE WIDTH •Equal to the Input: No pulse width conversion (difference between input and output within ±10 μsec.) • One-shot Output: Constant pulse width Output Frequency (Hz) = 500 / (Output Pulse Width (msec.)) Adjustable pulse width Pulse width max. 30 msec. (code 2): 1 – 30 msec. adjustable (standard 5 msec. ±20 %) for 'Output' code other than 'H' 10 – 30 msec. adjustable (standard 10 msec. ±20 %) for 'Output' code 'H' Pulse width min. 30 msec. (code 3): 30 msec. – 1 sec. adjustable (standard 50 msec. ±20 %)


Buy Now

Dds Function Signal Generator Module Sine Square Sawtooth  Wave Kit X6f6 picture
Dds Function Signal Generator Module Sine Square Sawtooth Wave Kit X6f6


Lmx2594 10mhz-15ghz Rf Signal Generator Frequency Source Sweep + Oled New  picture
Lmx2594 10mhz-15ghz Rf Signal Generator Frequency Source Sweep + Oled New


Fpa2000 Dc12v 30w Signal Power Amplifier Module Signal Amplifier Low Distortion picture
Fpa2000 Dc12v 30w Signal Power Amplifier Module Signal Amplifier Low Distortion


Dc12v High Precision Signal Power Amplifier Module 100khz For Signal Generator picture
Dc12v High Precision Signal Power Amplifier Module 100khz For Signal Generator